LCAM0336OD Cam unresponsive
HelloBuya cameraLinksysLCAM0336ODand does not allowmeaccess.No accessbydefault IP192.168.1.254.NoracquiresipfromDHCPserver.Tryusing the internalresetbutton anddoes not.TheStatusLEDdoes not...
View ArticleRe: LCAM0336OD 1080p - Black screen in webinterface
Thank you for your answers! I have tested all agents and documents modes, everytime the same result -> black screen/no video But I have found a way to show the picture: The camera is accessed via a...
View ArticleRe: LCAM0336OD Cam unresponsive
Hi, LMR. Let's isolate this. Did you try and perform a hard reset by pressing and holding the reset button for 30 seconds while the device was ON? Was your computer on a static IP that is in the same...
View ArticleRe: LCAM0336OD Cam unresponsive
If none of the LED's light up under any circumstances than the device is probably defective and should be returned to store of purchase for replacement.
View ArticleRe: LCAM0336OD Cam unresponsive
Thanks for your reply. Only the status LED does not light. The internal reset does not work. I let down the internal reset button and there is no change. No access by default IP address, the cam does...
View ArticleRe: LCAM0336OD Cam unresponsive
Thanks for your reply. The computerfrom whichI try toaccess thecamera is on the same subnet.. The internal reset does not work. I let down the internal reset button and there is no change. No access...
View ArticleRe: LCAM0336OD Cam unresponsive
@LMR If doing the reset didn't work and we are still unable to communicate with the camera, the camera seems to be defective and needed to be replaced. You can email us at LinksysCares@linksys.com with...
View ArticleRe: Using the 192.168.1.115 IP address I can ot get into the camera.
como faso para pasa u videos de meu dvr para meu conputado
View ArticleRe: LCAD03VLNOD itself does not record anything
Eric Jan, How good is the motion detection? I have not made it work properly, either it is too sensitive or too unsensitive. How relevant are the recordings? JA
View ArticleClik here to view.
Re: LCAD03VLNOD itself does not record anything
The motion sensor works pretty well over here. in IE browser you can easily set the sensitivity and the threshold when it should start recording, although i'm still at test setup here it seems to work...
View ArticleRe: LCAD03VLNOD itself does not record anything
Eric, What I mean with "relevant" is that there is movement in the scene, of course, and all movements in front of the camera get recorded. Everything, of course, above a given threshold. Is that the...
View ArticleRe: LCAD03VLNOD itself does not record anything
@jaba. It's good to know that you're able to save the motion using the SD card after you've reset and reconfigured the device. On the event settings, did you try to change the "Save Stream to" and...
View ArticleLCAD03FLN Email settings and Samba settings!
Hi all, I have just purchased a LCAD03FLN camera. It is located on a work network and needs access to the work email server (which has no login for the same subnet) and also access to our fileshare....
View ArticleRe: Cannot read AVI files
It is totally ridiculous that Linksys somehow decides to screw-up the video files.The recorder does not have sufficient computation power to transcode the streams.Therefore, they MUST be stored in...
View ArticleRe: Cannot read AVI files
I dug into this problem a little further and it seems not to be so big after all.Linksys, for unknown reasons, changes the FOURCC code of the AVI File (that defines which video stream is stored inside...
View ArticleRe: Cannot read AVI files
OK Linksys Support, we are doing your job. Please provide a solution for us Mac users.
View ArticleRe: Cannot read AVI files
@jaba: you should be able to compile most linux programs under Mac OS. Give it a try. Otherwise, find the corresponding tools for FourCC code changing (which is basically editing a field in the AVI...
View ArticleRe: Cannot read AVI files
@jaba. The LNR0208C (network video recorder) requires the NVR Player to be installed in a Windows-operated computer. This software includes the required codec for the raw .avi file to be played either...
View ArticleRe: Cannot read AVI files
As already pointed out in my previous posts, this is bad by design. The AVI file is just a container around a raw video stream. By changing the FourCC code in the AVI header, the Linksys engineers...
View ArticleRe: LCAD03FLN Email settings and Samba settings!
Hi, Andrewjones216! For the Email settings, there is no option to configure it without a username and password. You'll have to create an account for the mail server. For the Samba Settings, you should...
View Article